Shopping Cart

0 item(s) - 0.00€
Your shopping cart is empty!

Vamo VV/VW Mod Body V2

Vamo VV/VW Mod Body V2
Vamo VV/VW Mod Body V2 Vamo VV/VW Mod Body V2 Vamo VV/VW Mod Body V2 Vamo VV/VW Mod Body V2
Brand: Rainbow Heaven Technology Co., Ltd
Product Code: Vamo-Body
Availability: Out Of Stock
Price: 44.95€ 29.95€

Available Options

* Color:

Add Vaporizer:

Add Lanyard:

Add extras:

Add extras:

   - OR -   

This device is getting rave reviews for being the budgetprice Variable Wattage (VW) and Variable Voltage (VV) device that performs really very well. It should work well with most atomizers with 510 and eGo connections and in variable wattage mode it should adjust automatically to suit most resistance atomizers (above 1.2 ohms). The Vamo has a 1.2 ohm cut off feature.

The VAMO is an inexpensive mod with an impressive list of features.

The specifications of chrome Vamo VV/VW Mod Body V2 :

  • Metal buttons
  • Variable Volt: 3~6.0V, 
  • Variable Watt: 3~15W. 
  • Thread: 510/eGo
  • PWM (Pulse Width Modulation) output, up to 5 amps
  • 5 click on/off
  • Multiple battery options (1 x 18650, 1 x 18350 or 2 x 18350)
  • Reverse and short protection
  • Low resistance and low battery warning

Box contents:

  • Vamo VV/VW Mod Body V2 - 1 pcs

When fully assembled the Vamo mod can accommodate one 18650 or two 18350 batteries. By removing one body section, a single 18350 battery may be used. Protected batteries are not required.

How to use chrome Vamo VV/VW Mod Body V2:

Turn On or Off:
Press the Power (large) button 5 times within 2 seconds.
Switch between VV and VW:
Press and hold + and - buttons for 3 seconds (V for volts, W for Watts).
Voltage adjust:
Tap the + or - buttons to raise or lower output voltage (in .1 volt increments).
Wattage adjust:
Tap the + or - buttons to raise or lower output wattage (in .5 watt increments).
Resistance check:
With an atomiser or cartomiser installed on unit, press and hold the + button for 2 seconds. Atomiser resistance is displayed in ohms.
Battery voltage check:
Press and hold the - button for 2 secs to check actual battery voltage
The Vamo can display output voltage and wattage as an Average or as RMS (Root Mean Square). RMS is the actual and true output and is the one to use.
Press and hold the + button for 10 secs. If  no2 is shown then the output is already set to RMS, no further action is required. If no1 is shown, release the button and press again for 10 secs until the display shows no2. This setting should not alter after a battery change, however if the vape feels warmer than expected please re-check setting.
Error codes:
LO-Ω : Atomiser resistance is too low (below 1.3 ohm).
LO-v : Atomiser shorted
Display will flash when battery needs replacing/recharging (approx 3.4v).
Voltage or wattage level resets when battery is removed, the mode does not.
Usage of eGo style cartomisers/clearomisers:
The Vamo has a recessed atomiser fitting with a large opening to accommodate the eGo skirt. Most popular atomisers and cartomisers will fit, however if you use a wide skirted unit (eg: Kanger T2 or T3 clearomizer) you will need to fit a 510-EGO adaptor.

Video review and instructions (Version 2):

Write a review

Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:

Area IT
e-CigShop.eu © 2014